Кафедра будівництва та інфраструктурної інженерії
Постійне посилання на фондhttps://repository.lntu.edu.ua/handle/123456789/55
Переглянути
109 результатів
Результати пошуку
Item type:Наукова стаття, Study of change strength and deformation properties of wood under the action of active acid environment(2023) Homon, Sviatoslav; Gomon, Petro; Gomon, Svyatoslav; Vereshko, Oleg; Boyarska, Inna; Uzhegova, OlgaExperimental studies of birch and pine wood by axial compression along the fibers under the action of active acidic environment with different soaking time were carried out. The complete deformation diagrams "stress σс - longitudinal deformation uс" of the examined wood species under such conditions were constructed. On the basis of the experiment, the actual values of ultimate strength, critical and residual (final) deformations of birch and pine wood under the action of an active acidic environment with different soaking time were determined. It was found that exposure to an acidic environment for 28 days of soaking significantly reduces the strength and increases the deformation characteristics of the studied wood samples compared to those at standard humidity. Under such conditions, the ultimate strength decreases by 42.4%; critical deformations increase by 18.5%, and residual deformations increase by 24.8%. It is also proved that the obtained mechanical characteristics depend on the soaking time with various aggressive environment and their concentration.Item type:Наукова стаття, Features of the work of reinforced concrete arches with adjustment of effort under repeated loads(2024-11-29) Кислюк, Дмитро Ярославович; Савенко, Володимир Іванович; Ужегова, Ольга Анатоліївна; Самчук, Володимир Петрович; Нінічук, Микола ВолодимировичЕкспериментально досліджено роботу двошарнірних залізобетонних арок, що дає можливість дослідити особливості напружено-деформованого стану перерізах поясу та характер перерозподілу зусиль арки між верхнім поясом та затяжкою, розвитку прогинів та тріщин при одноразових та повторних короткочасних статичних навантаженнях. Наведено методику розрахунку внутрішніх зусиль двошарнірних залізобетонних арок із врахуванням перерозподілу зусиль при повторних навантаженнях.Item type:Наукова стаття, Study of wood deformation indicators after exposure to acidic environments(2026) Vereshko, Oleg; Boyarska, Inna; Uzhegova, Olga; Shevchuk, Pavlo; Uzhehov, Serhii; Homon, Sviatoslav; Gomon, Svyatoslav; Gomon, PetroExperimental studies were conducted on the deformation indicators of structural birch and pine wood under the influence of various acidic environments with different impregnation times. The deformation parameters of all studied wood species were determined experimentally, in particular the critical uc,0,d,agr and residual deformations uc,fin,agr. It has been established that exposure to an acidic environment increases the deformation characteristics of structural timber.. Specifically, the relative critical deformations of the studied species increased within the range of 1.12 to 1.17 times after 28 days of impregnation compared to the samples tested at the standard moisture content of 12%, and within the range of 1.14 to 1.19 times after 180 days. Residual deformations increased 1.1 to 1.25 times after 28 days of impregnation, and after 180 days, they remained practically the same. Over the following five months, the strength and deformability characteristics changed insignificantly, they stabilized. This is explained by the fact that after 28 days of impregnation, the wood is almost completely saturated with moisture and subsequently hardly absorbs any more.Item type:Наукова стаття, Перевірка міцності стін та основ укриття для розробки плану реконструкції головного корпусу волинської обласної дитячої клінічної лікарні(Луцьк: ЛНТУ, 2023-07-23) Ротко, Світлана Володимирівна; Парфентьєва, Інна Олександрівна; Пасічник, Руслан Володимирович; Ужегова, Ольга Анатоліївна; Чапюк, Олександр СергійовичТехнічний огляд є однією з головних умов розробки проекту реконструкції будівлі. Виявлення наявних дефектів дозволяє прогнозувати так звані проблемні ділянки в елементах конструкцій, які необхідно перевірити на можливість подальшої експлуатації та, за необхідності, передбачити заходи щодо їх посилення. Проведенню технічного огляду конструкцій укриття головного корпусу Волинської обласної дитячої клінічної лікарні у Луцьку передувала необхідність перевірки його міцності для подальших рекомендацій щодо проекту реконструкції. План реконструкції передбачає надбудову кількох поверхів для розширення професійної діяльності закладу та збільшення кількості ліжок. Реалізація цього проекту, відповідно, призведе до значного збільшення навантаження на фундаменти будівлі. Тому, враховуючи пропозиції щодо надбудови, необхідно насамперед оцінити поточний стан несучих конструкцій, перевірити міцність стін та фундаментів на підвищене навантаження, а також надати рекомендації щодо експлуатаційних властивостей цих елементів. В результаті технічного обстеження конструкцій укриття головного корпусу Волинської обласної дитячої клінічної лікарні було встановлено, що під час експлуатації будівлі конструкції отримали кілька дефектів та пошкоджень, але їх стан можна вважати задовільним. У зв'язку із запланованою надбудовою кількох поверхів, розрахунки стін та фундаментів укриття були виконані виходячи з ваги існуючих конструкцій та додаткової ваги проектованої надбудови - 25 т/м.п. Перевіркою міцності несучих стін на задане додаткове навантаження від проектованих верхніх поверхів будівлі було встановлено, що міцність стін укриття забезпечується з десятикратним запасом. Перевіркою міцності та надійності фундаментів було встановлено, що запас міцності фундаменту становить 67%.Item type:Наукова стаття, Аналіз ефективності використання високоміцних бетонів у стиснутих елементах монолітних каркасних будівель(Луцьк: ЛНТУ, 2025-01-18) Ротко, Світлана Володимирівна; Ужегова, Ольга Анатоліївна; Задорожнікова, Ірина Вікторівна; Рябий, Олександр ІгоровичTraditionally, reinforced concrete is the most common material for constructing multi-story civil buildings. Modern construction is characterized by a significant increase in the number of storeys of buildings and at the same time a significant increase in the complexity of architectural solutions. Therefore, high-strength concretes are quite popular materials, especially in implementing ambitious architectural projects, where it is necessary to ensure high strength and reliability of structural elements. The issue of increasing the strength and durability of concrete has long been on the agenda of scientists around the world. Many of them believe that the main method of improving the physical, mechanical construction, and operational indicators of concrete is to ensure the quality of its micro- and mesostructure, i.e., high density, impermeability, and minimal cracking. It has been proven that the use of high-quality aggregates, highly active cement, and a low W/C ratio is the simplest and most economical way to obtain high-strength concrete using traditional manufacturing technology. Among the advantages of using high-strength concretes are higher early strength, the possibility of early stripping (and therefore, earlier commissioning of the facility), increased load-bearing capacity, reduced costs for formwork due to a reduction in the cross-section of structural elements (respectively, a reduction in the weight of the latter, and therefore, the load on the structures below). This, in turn, will contribute to a reduction in the volumes of concrete and reinforcement, i.e., the installation mass of the elements, and, accordingly, a reduction in transport costs for the delivery of materials. Important advantages are also higher density, water and gas impermeability due to a reduction in capillary pores, increased resistance to chemically active substances; high corrosion resistance, and therefore, protection of reinforcement; and reduced costs for formwork. The paper studies the feasibility of using high-strength concrete for the manufacture of vertical elements operating in compression - columns and pylons of multistory residential buildings. To study the effectiveness of the use of high-strength concrete, a monolithic 13-story frame residential building with commercial premises located on the first floor was taken. The calculation was carried out in the MONOMAKH-SAPR PC using the finite element method (FEM). The study found that replacing concrete in columns of class C20/25 with concrete of class C50/60 allowed a total economic effect of 223,693 thousand UAH due to the reduction in the cross-sectional dimensions of the columns and the reduction in the cost of reinforcing steel. The savings on materials amounted to 17.9%. It is also important that the useful area of the building increased when the cross-sections of the columns were reduced, which will also have a significant economic effect. Therefore, we can conclude that it is economically feasible to use high-strength concrete for columns of multi-story buildings, especially in high-rise construction.Item type:Методичне забезпечення, CAD in Construction(Lutsk: LNTU, 2026) Ротко, Світлана ВолодимирівнаThe methodological development includes thematic planning of students' independent work, questions for self-control, tasks for independent study, and recommended literature for working within the LIRA-FEM and MONOMAKH-SAPR software complexes.Item type:Методичне забезпечення, Основи та фундаменти(Луцьк: ЛНТУ, 2026) Парфентьєва, Інна ОлександрівнаВидання містить вказівки до виконання курсового проекту, довідковий матеріал, необхідний для розрахунків та приклади оформлення елементів графічної частини курсового проекту. Призначене для здобувачів першого (бакалаврського) рівня вищої освіти освітньої програми «Будівництво та цивільна інженерія» галузі знань денної та заочної форм навчання.Item type:Методичне забезпечення, Організація та управління в будівництві(Луцьк: ЛНТУ, 2026-04) Дробишинець, Сергій ЯрославовичМетодичні вказівки призначені для виконання розрахунково-графічної роботи при вивченні тем лекцій «Календарне планування у будівництві», «Поточна організація будівництва», «Розробка і проектування будівельних генеральних планів». Наведено склад і послідовність виконання розрахунково-графічної роботи. Наведено основні визначення, пояснення та довідкові дані по таких темах: визначення номенклатури, об’ємів i трудових витрат будівельно-монтажних робіт; вибір монтажних кранів; проектування календарного плану; розрахунок об’єктного будгенплану; розрахунок площі складів; розрахунок тимчасових адміністративно-побутових будинків; розрахунок тимчасового водопостачання будівельного майданчика; розрахунок тимчасового електрозабезпечення будівельного майданчика; техніко-економічні показники будгенплану.Item type:Методичне забезпечення, Проєктування в AutoCAD Civil 3D(Луцьк: ЛНТУ, 2026-04) Ясюк, Іван МиколайовичМетодичне видання до практичних робіт розроблено відповідно до робочої програми дисципліни «Проєктування в AutoCAD Civil 3D» та містить методичні рекомендації і завдання до практичних робіт, спрямованих на опанування системи автоматизованого проєктування AutoCAD Civil 3D для інженерів-будівельників.Item type:Методичне забезпечення, Будівельна техніка і виробнича база будівництва(Луцьк: ЛНТУ, 2026-04) Чапюк, Олександр Сергійович; Пахолюк, Орест АндрійовичУ методичних вказівках самостійної роботи наведено постановку задачі, порядок розрахунків i короткі пояснення до виконання самостійної роботи з курсу „Будівельна техніка та виробнича база будівництва”. Методичне видання складене відповідно до програми нормативної дисципліни професійного спрямування «Будівельна техніка та виробнича база будівництва» та призначене для здобувачів, які навчаються на ОП «Будівництво та цивільна інженерія» денної та заочної форм навчання.