Кафедра будівництва та інфраструктурної інженерії
Постійне посилання на фондhttps://repository.lntu.edu.ua/handle/123456789/55
Переглянути
171 результатів
Результати пошуку
Item type:Наукова стаття, Designing reinforced plywood panels through deformation methods(2025) Gomon, Petro; Drobyshynets, Serhii; Smal, Mariia; Dziubynska, Oksana; Uzhegova, Olga; Golyk, Yolana; Kaynts, Diana; Kutsyna, IrynaA deformation methodology for theoretical and mathematical modelling and calculation of composite-reinforced plywood panels is proposed. The stages of the stress-strain state of a reinforced bending wooden element (plywood panel) with metal reinforcement are presented. An algorithm for constructing a ‘moment-curvature’ graph of a reinforced wooden element (plywood panel) is proposed.Item type:Наукова стаття, Establishing patterns in the formation of a fire-resistant sip panel with hemp insulation(2026-02-27) Tsapko, Yuriy; Tsapko, Аleksii; Berdnyk, Oksana; Likhnyovskyi, Ruslan; Bielikova, Kseniia; Slutska, Oksana; Borysova, Anna; Lomaha, Vasyl; Uzhehova, Olha; Chaikovskiy, VitaliiThis study investigates the process that forms fire-resistant properties of SIP-panels with hemp insulation based on reactive coating and lime. The task addressed is to ensure the stability of SIP-panels and components when treated with coatings to changes in operating conditions. This is important since production from renewable sources for construction is a relevant issue. It has been proven that during thermal action on samples of hemp insulation treated with reactive coating and lime, no ignition and flame spread along the surface occurred. A layer of foam coke formed on the surface of the sample treated with reactive coating, which is 22 mm. The study has shown that when a burner is applied to a sample of SIP-panels with hemp insulation treated with reactive coating, after 110 s of thermal exposure, the process of forming a heat-insulating layer of coke began, which inhibited heat transfer. Instead, after the burner was exposed to a sample of SIP panels with hemp insulation treated with lime, a charring process occurred at the site of thermal action, but ignition and flame spread did not occur. Based on the results of determining the strength, it was found that treating the surface of hemp insulation with a coating increases the tensile strength by more than 2.5 times. Thus, increasing the amount of reactive coating on the surface of hemp insulation by half increases the tensile strength by 2.3 times. In the case of treating hemp insulation with lime, the tensile strength decreases by 3.4 times while increasing the amount of lime when treating the surface of hemp insulation to 0.38 kg/m2 increases the tensile strength by 5.3 times. Thus, there is reason to argue about the possibility to design effective and operationally stable biocomposites for construction.Item type:Наукова стаття, Study of wood deformation indicators after exposure to acidic environments(2026) Vereshko, Oleg; Boyarska, Inna; Uzhegova, Olga; Shevchuk, Pavlo; Uzhehov, Serhii; Homon, Sviatoslav; Gomon, Svyatoslav; Gomon, PetroExperimental studies were conducted on the deformation indicators of structural birch and pine wood under the influence of various acidic environments with different impregnation times. The deformation parameters of all studied wood species were determined experimentally, in particular the critical uc,0,d,agr and residual deformations uc,fin,agr. It has been established that exposure to an acidic environment increases the deformation characteristics of structural timber.. Specifically, the relative critical deformations of the studied species increased within the range of 1.12 to 1.17 times after 28 days of impregnation compared to the samples tested at the standard moisture content of 12%, and within the range of 1.14 to 1.19 times after 180 days. Residual deformations increased 1.1 to 1.25 times after 28 days of impregnation, and after 180 days, they remained practically the same. Over the following five months, the strength and deformability characteristics changed insignificantly, they stabilized. This is explained by the fact that after 28 days of impregnation, the wood is almost completely saturated with moisture and subsequently hardly absorbs any more.Item type:Наукова стаття, The influence of repeated low-cycle loads on the stress-strain state of steel-reinforced concrete drainage gutters(2026) Andriichuk, Oleksandr; Yasiuk, Ivan; Uzhegova, Olga; Uzhehov, SerhiiThe paper presents the results of experimental studies on the effect of repeated low-cycle loading on the stress–strain state of steel fiber reinforced concrete gutters. A comparison was made between the effects of single and repeated loadings. Overall, the findings demonstrate that steel fiber reinforced concrete gutters have higher resistance to cyclic loading compared to single loading, and they better withstand repeated impacts without significant material failure.Item type:Наукова стаття, Аналіз ефективності використання високоміцних бетонів у стиснутих елементах монолітних каркасних будівель(Луцьк: ЛНТУ, 2025-01-18) Ротко, Світлана Володимирівна; Ужегова, Ольга Анатоліївна; Задорожнікова, Ірина Вікторівна; Рябий, Олександр ІгоровичTraditionally, reinforced concrete is the most common material for constructing multi-story civil buildings. Modern construction is characterized by a significant increase in the number of storeys of buildings and at the same time a significant increase in the complexity of architectural solutions. Therefore, high-strength concretes are quite popular materials, especially in implementing ambitious architectural projects, where it is necessary to ensure high strength and reliability of structural elements. The issue of increasing the strength and durability of concrete has long been on the agenda of scientists around the world. Many of them believe that the main method of improving the physical, mechanical construction, and operational indicators of concrete is to ensure the quality of its micro- and mesostructure, i.e., high density, impermeability, and minimal cracking. It has been proven that the use of high-quality aggregates, highly active cement, and a low W/C ratio is the simplest and most economical way to obtain high-strength concrete using traditional manufacturing technology. Among the advantages of using high-strength concretes are higher early strength, the possibility of early stripping (and therefore, earlier commissioning of the facility), increased load-bearing capacity, reduced costs for formwork due to a reduction in the cross-section of structural elements (respectively, a reduction in the weight of the latter, and therefore, the load on the structures below). This, in turn, will contribute to a reduction in the volumes of concrete and reinforcement, i.e., the installation mass of the elements, and, accordingly, a reduction in transport costs for the delivery of materials. Important advantages are also higher density, water and gas impermeability due to a reduction in capillary pores, increased resistance to chemically active substances; high corrosion resistance, and therefore, protection of reinforcement; and reduced costs for formwork. The paper studies the feasibility of using high-strength concrete for the manufacture of vertical elements operating in compression - columns and pylons of multistory residential buildings. To study the effectiveness of the use of high-strength concrete, a monolithic 13-story frame residential building with commercial premises located on the first floor was taken. The calculation was carried out in the MONOMAKH-SAPR PC using the finite element method (FEM). The study found that replacing concrete in columns of class C20/25 with concrete of class C50/60 allowed a total economic effect of 223,693 thousand UAH due to the reduction in the cross-sectional dimensions of the columns and the reduction in the cost of reinforcing steel. The savings on materials amounted to 17.9%. It is also important that the useful area of the building increased when the cross-sections of the columns were reduced, which will also have a significant economic effect. Therefore, we can conclude that it is economically feasible to use high-strength concrete for columns of multi-story buildings, especially in high-rise construction.Item type:Наукова стаття, Особливості методики інтеграції інженерних мереж з тепловим насосом у будівлю в долині річки Сапалаївки у Луцьку(Луцьк: ЛНТУ, 2025-07-24) Синій, Сергій Васильович; Гупік, Наталія Василівна; Ксьоншкевич, Любов Миколаївна; Крантовська, Олена Миколаївна; Ужегова, Ольга Анатоліївна; Ротко, Світлана ВолодимирівнаАналіз літературних джерел показав стійкі тенденції: технічного і технологічного розвитку інженерних мереж в напрямку використання розумних і інтелектуальних технологій; ріст вимог до енергоефективності і екологічності інженерних мереж та об'єктів будівництва, в які ці мережі інтегруються. Проаналізовано приклади гідроморфологічної трансформації міських річок. Зроблено висновок про важливість збереження екосистеми Сапалаївки для Луцька. Проаналізовано особливості існуючого урбаністичного ландшафту Луцька навколо річки Сапалаївки. Детальніше проаналізовано стан ділянки рекреаційної зони Сіті-парку у долині цієї річки. Відзначено нові зміни урбаністичного ландшафту південного схилу: його укріплено залізобетонною стіною з контрфорсами. Біля схилу заплановано будівництво громадської будівлі з інтеграцією інженерних мереж з тепловим насосом. Розроблено удосконалену методику досліджень, яка передбачає різнобічний аналіз характеристик об'єкта досліджень. Аналізуються містобудівний, екологічний, соціально-економічний, архітектурно-будівельний аспекти. Такий науковий підхід дозволяє досягти в процесі проєктування найбільш збалансованих технічних рішень. Їх впровадження сприятиме досягненню кращих результатів з інтеграції інженерних мереж у об'єкти будівництва. Результати проєктування отримані в програмному середовищі Uponor. Для проведення аналізу в межах розробленої методики пропонується залучати відомі методологічні підходи. Залежно від потреб аналізу вони можуть бути різної математичної складності: від принципів SWOT-аналізу до методів аналізу та/або оптимізації з отриманням цільових функцій. Оптимізацію рекомендується проводити в один етап (визначати цільову функцію залежно від факторів, що є показниками аспектів) або у два етапи (коли показники аспектів також визначаються як цільова функція від факторів у складі кожного аспекту). Розроблену методику рекомендується використовувати як методичний підхід до вирішення складних проєктних рішень з інтеграції інженерних мереж в об'єкти будівництва. Вона покращує узгодженість таких рішень з містобудівними і екологічними вимогами до урбаністичного ландшафту.Item type:Наукова стаття, Restoration the functioning of engineering networks with reinforced concrete structures damaged during shelling(2025-12-04) Ksonshkevych, Liubov; Krantovska, Olena; Synii, Sergii; Uzhehov, Sergii; Uzhehovа, OlhaAn important component of critical snfrastructure is the facilities of engineering networks, which in the current conditions of war in Ukraine are exposed to shelling from various types and calibers of conventional weapons. These include pumping stations, boiler houses, and other reinforced concrete structures of water supply, sewerage and heat supply systems. Rapid and efficient restoration of these facilities is crucial for maintaining the functioning of engineering networks. Given the limited time and resources for new construction during wartime, priority is given to reconstruction and repair based on the results of technical inspections of damage. Restoration efforts first focus on the load-bearing reinforced concrete elements, such as columns and beams, with one of the urgent measures being their strengthening. Based on an analysis of methods and technologies for reinforcing reinforced concrete structures, the use of wet shotcreting with high-strength concrete is proposed. Shotcreting continues to evolve, including its application in 3D printing of reinforced concrete structures, and offers advantages such as the absence of formwork (which accelerates concreting), the availability of concrete, and the excellent protective properties of reinforced concrete under shelling, including high strength, rigidity, and resistance to high temperatures, fragment impacts and air shock waves. Using the example of strengthening load-bearing reinforced concrete columns, improvements to wet shotcreting technology through preliminary mechanoactivation of the binder (ordinary Portland cement + 10% microsilica + 1% SNF = 1%) have been introduced, allowing for the creation of high-strength protection (class C32/40...C70/85). This creates additional opportunities for mechanization, automation of wet shotcreting of reinforced concrete structures of engineering networks.Item type:Навчальний посібник, Дискретно-воксельний параметричний дизайн у MagicaVoxel(Луцьк: Вежа-Друк, 2026) Пустюльга, Сергій Іванович; Самчук, Володимир ПетровичУ навчальному довіднику авторами розглянуто основні можливості програми MagicaVoxel: від встановлення та базових інструментів до створення складних композицій і експорту в потрібний формат для подальшої роботи або рендерингу. Тут, у структурованому порядку, наведені практичні приклади, поради, а також вправи для самостійного створення різного роду воксельних моделей. Значна увага приділена способам створення проєктів із використанням дискретно-параметричного підходу. Кожен розділ включає ілюстрації та покрокові інструкції, щоб зробити навчання легким і зрозумілим.Item type:Методичне забезпечення, Проектування доріг та споруд(Луцьк: ЛНТУ, 2026) Процюк, Віталій ОлексійовичКонспект лекцій розроблено відповідно до робочої програми дисципліни «Проектування доріг та споруд». Видання містить питання для розгляду та практичні завдання, розв’язання яких сприятиме засвоєнню теоретичного матеріалу з проектування автомобільних доріг та споруд транспортної інженерії.Item type:Методичне забезпечення, CAD in Construction(Lutsk: LNTU, 2026) Ротко, Світлана ВолодимирівнаThe methodological development includes thematic planning of students' independent work, questions for self-control, tasks for independent study, and recommended literature for working within the LIRA-FEM and MONOMAKH-SAPR software complexes.