scientificarticle.page.titleprefix Автоматизований розрахунок плити на пружній основі на додаткове навантаження
Loading...
Date
Journal Title
Journal ISSN
Volume Title
Publisher
Луцьк: ЛНТУ
Abstract
Проведено технічне обстеження та оцінку стану залізобетонної плити
підлоги корпусу №14 СП ТОВ «Модерн-Експо», по вулиці. Рівненська, 4 села
Струмівка. За результатами обстеження виконано перевірочний розрахунок
несучої здатності плити підлоги від коліс навантажувача Linde H100D/600.
Плита підлоги розраховувалась як плита на пружній основі. В якості в’язів при
розрахунку задано існуючий грунт, а також фундаменти під колони. Крок колон
становить 6 м в обох напрямках. Для визначення максимальних напружень
навантажувач передніми колесами розміщували в центрі та по краях фрагменту
плити 6х6 м. У результаті було знайдено найбільш невигідне положення вантажу
на плиті та виконано перевірочний розрахунок.
Description
A technical inspection and assessment of the condition of the reinforced concrete
floor slab of building No. 14 of JV "Modern-Expo" LLC, Rivnenska street, 4 Strumivka
villages. The survey was carried out by specialists of the Scientific and Research
Construction Laboratory of the Lutsk National Technical University at the Department of
Construction and Civil Engineering. Based on the results of the survey, a verification
calculation of the load-bearing capacity of the floor slab was performed based on the
weight of the slab and the wheels of the Linde H100D/600 forklift. The floor slab was
calculated as a slab on an elastic base. The existing soil and foundations under the
columns are supports for the slab. Columns are placed with a step of 6 meters in both
directions. The base soil consists of crushed stone, bulk soil, humus loess sand, loess
sand, fine sand (according to the engineering and geological conclusion)
To determine the maximum stresses, two positions of the loader on a 6x6 m slab
fragment were considered. Positions 1. The geometric center of the loader is placed in
the middle of the slab. The load from the wheels is taken according to the technical
characteristics. The front wheels transmit a load of 12.4525t each to the plate. The rear
wheels transmit a load of 1.697t each to the slab. Positions 2. The front axle of the loader
is placed in the middle of the slab. The load from the wheels is taken according to the technical characteristics. The front wheels transmit a load of 12.4525t each to the plate.
The rear wheels transmit a load of 1.697t each to the slab.
As a result, the position in the first variant, when the geometric center of the loader
is placed in the middle of the plate, turned out to be the most unfavorable position.
After carrying out a verification calculation of the bearing capacity of the floor
slab from the own weight of the slab and the wheels of the Linde H100D/600 loader
according to the first load option, a conclusion was made about the sufficient bearing
capacity and the possibility of using the slab under the planned loads.
Keywords
плита на пружній основі, залізобетонна плита, напруження
Citation
Пасічник Р. В., Ротко С. В., Лучинець С. А., Пасічник О. С. Автоматизований розрахунок плити на пружній основі на додаткове навантаження. Сучасні технології та методи розрахунків у будівництві. 2023. Вип. 19. С. 135–140.